Features
- Visible at a distance with crisp, colorful LED bar on top of unit with flip screen
- Remote viewing through the web
- Stands up to harsh conditions
- Duty cycle and k-factor multiplier options
- Flexible uses throughout your plant
- Easy to choose the target gas
- Quick start-up for emergency response
- Easy to use with protective equipment or hazmat gear
- Data logging and information management for total confidence
- Easy maintenance and long-lasting battery
Specifications
Specifications
| Detection Technique |
Chemcassette tape-based with advanced self monitoring optics design and K-factor multiplier options. Duty cycle options to save paper. |
|---|---|
| Dimensions |
Height: 33.6 cm; Width: 18.3 cm; Depth without handle: 16.3 cm; Depth with handle: 24.1 cm |
| Weight |
4.1 kg |
| Mounting Screws |
Concrete: 5/16 in x 2 in vibration-resistant stud anchor for concrete (McMaster-Carr 94475A185 or equivalent), add 0.25 in. to length when mounting bracket with sun shield. Wood: 5/16 in. x 2 in. flange head lag screw for wood (McMaster-Carr 95526A375 or equivalent), add 0.25 in. to length when mounting bracket with sun shield. |
| Operating Temperature |
0°C to 40°C for most gases/applications |
| Operating Humidity |
0-100% RH for unit (Sample RH limited per tape/calibration). Sample line requires additional hardware to remove moisture in high RH conditions where condensing may occur. The sample must be non-condensing. Dry conditions may require humidification. |
| Flow System |
Automatic flow control with bypass system, higher flow at inlet to reduce sample time (internal bypass system); sample up to 100 ft, check manual for specific gases. |
| Local Alarms/ Status |
Visual: LEDs for alarm, normal condition, fault and external power. Audible: User selectable: Off, Low ~75 dB at 1 m, Medium ~85 dB at 1 m, High >90 dB at 1 |
| Interface |
4 large buttons, 3.5 in. Color LCD TFT display, web server. Flip screen. |
| Data Logging |
Rolling up to 3 months (15-22 sec. with no gas reading, 1-2 sec. when reading gas), Event history (1500 events – approx. 1 year). |
| Maximum Inlet/ Outlet Pressure Differential |
The overall maximum load on the pump between the inlet and the exhaust should not exceed 10” WC (24.8 mbars or 2488 Pascales). |
| Relays |
250V AC, 6 A maximum |
| USB |
2.0 or later. |
| Indoor/ Outdoor Use |
Both (the power supply provided is indoor only) |
| Operating Altitudes |
-1,000 to 3,000 ft. above sea level: standard; 3,000 ft. to 6,000 ft. above sea level: requires adjustment by Honeywell Analytics. |
| Ingress Protection Rating |
IP65 |
| External Switch or Circuit Breaker Requirement (Description & Location) |
Meet or exceed all local codes and regulations. |
| Ventilation Requirements |
Mount with no obstructions within 4 in. (10 cm) of either side or within 2 in. (5 cm) above and below the detector |
| Power Supply |
Universal Line powered (90-260 VAC 50/60 Hz) for battery charger |
| Power Consumption |
~1.9 A at 24 VDC +/- 10% (including battery-charging current). |
| Battery Type |
Lithium ion |
| Battery Life |
6+ hours under typical conditions – acts as battery back-up in fixed applications. Approximately 70% of its original capacity after 300 full charge/discharge cycles. |
| Power Adapter |
Input: 90~264 VAC, 1.2A, 47-63 Hz. Output: 24 VDC, 3.75 A max. |
| Wire Gauges |
Minimum: 24; Maximum: 14. AWG for relay and 4-20 mA outputs. |
| Communication Options |
Relays: Alarm 1, Alarm 2, Fault (user configurable for normally open/closed) 4-20mA Ethernet (with Modbus TCP/IP and web server). USB port (for memory stick configuration/data transfer). Communications connector and optional communications cable: 60 V, 5 A maximum |
Sensor Specs
Available Sensors
| Gas | Range |
|---|---|
| Arsine (AsH3) | 0.5-500ppb |
| Phosphine (PH3) | 3-3000 ppb |
| Diborane (B2H6) | 5-1000 ppb |
| Silane (SiH4) | 0.03 - 50 ppm |
| Germane (GeH4) | 50-2000 ppb |
| Hydrogen Selenide (H2Se) | 2-500 ppb |
| Hydrogen Sulphide (H2S) | 0.001-9.999 ppm |
| Hydrogen Fluoride (HF) | 0.02-20 ppm |
| Hydrogen Chloride (HCl) | 0.02-20 ppm |
| Hydrogen Bromide (HBr) | 0.02-10 ppm |
| Boron Trifluoride (BF3) | 0.05-10 ppm |
| Nitric Acid (HNO3) | 0.02-20 ppm |
| Sulfuric Acid (H2SO4) | 5-750 ppb |
| Hydrogen Iodide (HI) | 0.2-10 ppm |
| Chlorine (Cl2) | 0.005-5 ppm |
| Chlorine (Cl2) | 0.01-5 ppm |
| Fluorine (F2) | 0.01-10 ppm |
| Nitrogen Dioxide (NO2) | 0.03-10 ppm |
| Chlorine Dioxide (ClO2) | 20-1000 ppb |
| Ammonia (NH3) | 0.01-150 ppm |
| Dimethylamine (DMA, C2H7N) | 0.5-50 ppm |
| Tetrakis (Dimethylamido) Titanium (TDMAT, C8H24N4Ti) | 0.01-20 ppm |
| Trimethylamine (TMA, C3H9N) | 0.03-50 ppm |
| Phosgene (COCl2) | 2-2000 ppb |
| Ethylchloroformate (ECF, C3H5ClO2) | 0.02-30 ppm |
| Methylchloroformate (MCF, C2H3ClO2) | 0.03-30 ppm |
| Toluene Diisocyanate (TDI, C9H6N2O2) | 0.5-200 ppb |
| Methylene Bisphenyl Isocyanate (MDI, C15H10N2O2) | 0.5-200 ppb |
| Hexamethylene Diisocyanate (HDI, C8H12N2O2) | 0.5-150 ppb |
| Hydrogenated Xylene Diisocyanate (H6XDI, C10H14N2O2) | 0.5-150 ppb |
| Methylene bis-(4- cyclohexylisocyante) (HMDI, C15H22N2 O2) | 0.5-100 ppb |
| Isophorone Diisocyanate (IPDI, C12H18N2 O2) | 0.5-150 ppb |
| Xylene Diisocyanate (XDI, C10H8 N2 O2) | 0.5-200 ppb |
| Hydrazine (N2H4) | 3-1000 ppb |
| Monomethyl Hydrazine (MMH, CH6N2) | 3-2000 ppb |
| Dimethyl Hydrazine (UDMH, C2H8N2) | 3-2000 ppb |
| Hydrogen Cyanide (HCN) | 0.2-30 ppm |
| Sulphur Dioxide (SO2) | 10-2500 ppb |
| Ozone (O3) | 20-1000 ppb |
| Hydrogen Peroxide (H2O2) | 0.1-3 ppm |